DIY outside boot scraper and shoe brush

 This project is a great DIY that will save you money and can make a great gift depending on how fancy you want to get with it. 

    It is a basic shoe brush for knocking the dirt and mud off your shoes before coming into the house.     As you can see from the photo below I used a couple of scrap pieces of  2"X 8". The bottom one is approximately 14 inches in length and the side piece is about 7 to 8 in length. I screwed the short 2 x 8 at a right angle to the longer piece with 3" screws, making sure the screws are heavy enough to withstand being kicked and rubbed against.
The brushes are scrubbed brushes from the dollar store. They had a screw-on back that I removed and discarded and using the existing screw holes I used 1 1/2" screws to secure the brushes to the boards. Now I found these scrub brushes in the housewares section and could have just as easily used wooden brushes and simply predrilled my holes.
     And that was the complete project with a total cost of about four dollars. Now I could've gotten a little more fancy by adding a metal plate for scraping your boots on, but the heavy 2" X 8" I think will work just as well without. Now you could put Thompson's water seal on your project and that will help your project last a little bit longer. The main thing I was looking for was a shoe brush and boot scraper that wouldn't cost an arm and a leg. Most of the ones that I saw online were upwards of $15-$30 and the few that I tried didn't last more than one season. The worst-case scenario with this one is that I might have to replace the brushes at a total cost of three dollars.
     As it turns out, it also could turn into a moneymaker, as I've already had several people offer to pay upwards of $10-$15 for one.

So happy Nevada crafting and have a great day.

For other such projects sure to check out our website nevadacrafter.com and also be sure and check out our other blogs.

For free patterns and concept ideas http://patterns44.blogspot.com/
For more craft projects http://craft44.blogspot.com/
For 3-D pen project ideas http://3dpenideas.blogspot.com/

Toolbox Giftbasket

Toolbox Giftbasket

for

Him or Her

    Enlarge this design to whatever size you need.The length can be adjusted to however long you need. I recommend recessing the dowel handle or even drilling a hole all the way through for the dowel. Then hold in place with screws and or glue. Make sure you use the appropriate length screws and glue for the bottom and sides. Sand the sides of the project so that you can stain the wood afterward, but painting or decorating the box would probably also work. 

    Once you're finished with the project all you have left to do is to fill it with your favorite goodies for your favorite person and you will have a gift they will not soon forget. I love this project because it is such a versatile gift that can be given to him or her. It leaves them with something to use after they have consumed the goodies inside and could be used as a toolbox or even a planter for the front porch.

Be sure to checkout our web site www.nevadacrafter.com and our other blogs http://craft44.blogspot.com/ and http://nevadacrafter.blogspot.com/

DIY Bottle or Jar Cleaning Brush

Bottle or Jar Cleaning brush

This is a simple project with three main parts.

You will need the following.

1. Wooden spoon
2. Mop yarn
3. 4 inch foam mini paint roller
4. Hot glue - high temp.

The tools you will need are as follows

1. A sander of some type either belt sander or Dremel tool
2. quarter-inch drill bit and drill
3. hot glue gun with high temp glue.

Take the wooden spoon and sand the handle down just enough to fit inside the paint roller. Then drill 1/4 inch holes in the lower half the spoon, as shown here.

Then using a hot glue gun inject a small amount of blue inside the paint roller and long handle. Insert the handle into paint roller and immediately cool with cold water. The cold water is to keep the foam from melting and two quickset glue. Once you have glued the foam roller onto the handle it should not turn. If the roller rotates on the handle it will not do a very good job in cleaning bottles or jars. After you have assembled the foam handle you can use a crochet hook or latch hook or even micro forceps as seen here, to assemble the mop yarn. Mop yarn may be hard to come by at craft stores so I simply bought a mop from the dollar store and cannibalized it for the yarn. Yarn should be 6 to 8 inches in length and can be added to the spoon by either using half hitch knots or double knots on either side of the holes, so as to prevent the yarn from pulling through. You may want to add two or three strands per hole in order to get the right density of yarn. If you find that after assembly yarn is still too long you can simply trim with scissors. Once you have finished this your project is complete and you now have the best bottle brush ever. It's makes a great gift or a great project just for yourself.

    If you're going to make these for sale it is important to keep in mind that the cost of your materials is critical to whether it is profitable. Most of the materials were purchased at a dollar store and the cost of materials was kept under a dollar. Where you may lose some money as with any crafts is with the amount of time spent in creating the item. This may be offset by adding the item to a gift basket or similar project.  It may be possible to save a little bit of money by cutting out your own spoons out of quarter-inch wood stock. 

   Be sure to try different materials as well. Here we tried mop yarn, craft foam sheets cut into 1/2" X 4" strips and fabric netting. Each gives a different quality cleaning action. The netting is good for scrubbing tough stains, the foam works good at moving material and the mop yarn a good all around  material that holds water well.

Contest winner

Congratulations to Lisa Hess for being the month of May Nevada crafter contest winner.

Be sure and check our website and blogs for future contests and contest rules.
www.nevadacrafter.com

http://craft44.blogspot.com/

http://nevadacrafter.blogspot.com/

Contest for Nevada Crafter month of May

Nevada Crafter month of May contest

For your chance to win these 3 glass lampwork charms, great for making necklaces , bracelets or wine glass charms, all you have to do is follow or like us on one of the following.

Nevadacrafter on Facebook

Free Patterns and Ideas Blog

Craft 44 blog

Nevadacrafter blog

For future contests be sure and check out these sites and http://www.nevadacrafter.com

we are a Free Nevada Crafter online magazine

FREE Natural DIY Fiber Filling and Batting

I've been meaning to do this story for some time, as it actually has quite the history here in Fallon, Nevada. 

Milkweed, October 2015

    During World War II Japan cut off our supply of fiber fill (kapok) that was being used for making life vests, but a local weed came to the rescue. This plant that plagues farmers and gardeners alike is actually one of the most useful wild plants there is when it comes to textiles. My uncle told stories of kids going up and down ditch banks during the Great Depression collecting milkweed pods to sell the down. And I remember collecting monarch butterflies and yellow swallowtail butterfly caterpillar that feed on it. 

    It grows a seed pod that produces a hypoallergenic fiber fill that can be used in making pillows and stuffing quilts. The fiber is easily collected just before the pods open while the pods are still green. Pods are cracked and the seeds are raked off. You are then left with milkweed down that when allowed to dry makes an excellent fiber fill. There have also been a number of people who have experimented with combining it with other textile such as cotton or wool and then spinning that cotton or wool into yarn. (Sorry but I do not know the ratio used of cotton or wool to milkweed silk ) Unfortunately milkweed down by itself is too brittle for spinning but as I said before it has many unique and useful properties. Native Americans were also known to use the rubbery sap as a chewing gum by rubbing the sap between their fingers to make a rubber ball to chew on. Although I would not recommend it as it tastes awful and may be toxic, the white milky sap is similar to liquid latex. Fibers from the stem would also be used to weave into fishing line or cordage which was then used for making other things.

Drought and late in season, liberty pond

    It should be noted : before harvesting you should make sure that the milkweed has not been sprayed with an herbicide. If it smells funny or the leaves are brown then I would stay clear of these plants. The plants are readily found along ditch banks and ponds. And make sure you remove all the seeds, because if the seeds get wet, they will sprout.

Silky and soft to the touch

To me it is a mystery as to why this plant has not yet been commercialized, as it outperforms goose down. It is more breathable, more durable,and warmer than goose down. It also uses less water when compared to similar fiber crops. So if you’re looking for an inexpensive fiber fill this may make a

good alternative.

The green milkweed pods in the background of this photo are what you're looking to harvest just before they open 

Note green milkweed pods in background

milkweed at liberty pond

 

These beetles also make milkweed their home.

The fire and gem beetles are harmless and may be a good indicator that the plant has not been sprayed with herbicide or pesticide.

How do you humanely control roosting birds?

 Creating bird spikes with 3D pen

    In my first attempts at creating bird spikes, I simply used a quarter round or half round piece of old molding. Using a 16th inch drill bit I drilled numerous holes and then used the 3-D pen to partly fill the hole with extrusion from the pen and then moving outward creating spikes. 

     Although the finished product did not give me the rigidity in the spikes that I wanted it still seemed to work. 

In my last attempt I ran a bead of plastic at the bottom. This created better adhesion and stability to the spikes. I also tried creating lattice to give it additional rigidity, although I'm not sure that it was needed.
    The spikes do not harm the bird as they are not sharp enough or stiff enough to do so. They end up being more like the bristles on a soft broom and more of an obstacle that the bird can't quite figure out how to get around.
    A piece of styrofoam could be used in place of the wood, making it light enough to be stuck to a wall with poster putty. This might work great with woodpeckers and flickers that tend to roost on the sidewalls or under eaves .

Note: The Styrofoam will melt some with the 3D pen, so use gloves and some caution when working with it. 





     
I look forword to hearing any constructive ideas or suggestions. 

For this and other craft ideas checkout our other sites and be sure to subscribe.

www.nevadacrafter.com

http://craft44.blogspot.com/

http://patterns44.blogspot.com/

Nevada Crafter on YouTube